Booster Adapter (ADAP-CDE-F)
Finished module.

If you use the LDT low-cost Digital Booster DB-2 with a digital central unit which does not support a 5-pole booster bus and uses a 3-pole DCC-booster bus only. You can now use the Booster Adapter (adap-CDE).

The use of the DigitalBooster DB-2 on Lenz Digital plus Systems or with IB-BASIC, IB-COM and the PIKO Digi-Power-Box is now possible using this Booster Adapter adap-CDE.

Up to 10 Digital Booster DB-2/'s can be connected to each Adapter

Opto-couplers on the Adapter provide a separation between booster and digital central unit and therefore ensure safe electrical operation.

4-fold turnout decoder for DCC (S-DEC-4DC-F)

* For digital control of:

up to 4 twin-coil magnetic accessories (e.g. turnouts or signals)
up to 8 single-coil magnetic accessories (e.g. uncoupling tracks)
Up to four permanent power switch units (DSU) (e.g. for turnout-/ and road lights)

* The switching current is supplied to the decoder either from the digital circuitry or through a separate input directly from the alternating current (AC) output of a model railroad transformer (14 to 18V~). Valuable digital current can be saved !

* Simple and secure connection of turnouts, signals and uncoupling tracks by screw clips.

4-fold turnout decoder for DCC Digital (SA-DEC-4-DC-F)

*For the digital control of:

Illuminations and motors.
For consumers up to 4Ampere each output.
High-current turnout drives with end-switch: e.g. Märklin gauge 1 turnout and signal drives (without stressing the digital circuit).

* Simple and secure connection of the voltage supply and the consumers by screw clips.

* The switching-current for the 4 bistable relays will be supplied by the digital circuit or by a separate input from an alternating current output of a model railway transformer (14 to 18Volt ~) to the decoder. Valuable digital current can be saved!

*SA-DEC-4 is a 4-fold switch decoder (like the k84) but with a self learning decoder address:

The decoder address can be set by pushing the SA-DEC-4 programming key and the key of the turnout control board or by a switch command of your PC with connected INTERFACE.
The decoder address will be permanently stored but can always be changed by pressing the programming key again. It’s as simple as that !

* A ready to use finished module, 86 x 76 mm pc-board with four bores for mounting purposes are available (Suitable installation material can be ordered under accessories).

* The decoder from our Digital-Professional-Series can operate without any difficulty on your digitall model railroad. This decoder is 100% compatible with the Märklin-Motorola data format or the DCC standard.

*This finished module and the finished module in a case comes with a 24 month warranty.

* The SA-DEC-4 decoder will be supplied with a detailed operating- /assembly instruction.

The DigitalBooster DB-2 is a short circuit protected Power-Amplifier (Booster) for digital model railway layouts.

It supplies a digital current of 2,5 Ampere.

The DigitalBooster DB-2 is suitable for the digital formats Märklin-Motorola and DCC.

The DB-2 can be connected to any command station which supports the 5-poles booster bus:
Control Unit (Märklin-Motorola-Format), Central Station 1 and 2, Intellibox, EasyControl, ECoS, DiCoStation, KeyCommander (Märklin-Motorola- and DCC-Format) and TWIN-CENTER (DCC-Format).

Each Power-Amplifier DB-2 will be supplied with a 5-poles boosterbus-cable (1m length).

For the supply of the DigitalBooster DB-2 are model railway transformers suitable with a capacity of min. 50VA and an alternating current of 16 to 18 Volt (e.g. from Conrad Electronic Part No. 21 27 28 with 52VA / 18V).

If you want to use the DigitalBooster DB-2 on a command station which does not supports the 5-poles booster bus but only the 3-poles DCC-Boosterbus (clamp marking DCE) you can use the Booster-Adapter Adap-CDE.

If you want to use our low cost DigitalBooster DB-2 as well on Roco- or Fleischmann command stations (Roco Part No. 10761 and 10764 / Fleischmann Part No. 680901) and multiZENTRALEpro you can use the Booster-Adapter Adap-Roco.

LDT-Components from the Digital-Professional-Series can operate on your digital layout without any problems. The finished module and the finished module in a case comes with 2 years limited warranty.

Each DigitalBooster DB-2 will be supplied with a detailed operation- respectively assembly-instruction.